Owner’s Manual and User Guide. Ensure that you have the best possible experience with your Blendtec blender. • Owner’s manual.
I bought a used ibc7 with a bit over 13,000 15 second cycles. The upper bearing was pretty gummed up and there was bearing dust (a rusty powdery substance) I have seen before when a bearing goes out blown through the engine compartment. Looking at removing the socket? (the thing that receives the pitcher) shown in step 16. I think I need a vice with a 3/8 allen. Also, I would recommend lubing the two bearings shown in step 16 now and again to increase the life of the blender. It would not require a full teardown.
The rubber seals should pop open and a little cleaning and lube and all set. The bearings are 608rs which is a common available size. Hello Alberto, Did you finally figure out how to dis-assemble the top ring? Do you know where to buy any spare parts for Blendtec? I called up Blendtec and they clearly refused to send out any replacement parts saying that I need to send the blender and then they will estimate the repairs and will fix it if I agree to the repair charges. Bi Publisher Template Builder Download. Its a CON company who wanna charge the customers crazy amounts of money and won’t let anybody else touch the machine.
Install Ipx Protocol Windows 7 X64 Activator there. Please let me know if and how did you dis-assemble the top ring and get the rotor out. It's time to speak out for your right to repair We have a chance to guarantee our right to repair electronic equipment—like smartphones, computers, and even farm equipment. This is a once-in-a-generation chance to protect local repair jobs—the corner mom-and-pop repair shops that keep getting squeezed out by manufacturers. Join the cause and tell your state representative to support Right to Repair.
Tell them you believe repair should be fair, affordable, and accessible. Stand up for your right to repair!
• Xpress User Guide. • Table of Contents SECTION 1 – IMPORTANT SAFEGUARDS � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � SECTION 2 - COMPONENT OVERVIEW �. • Read all instructions carefully before using your Blendtec machine� 1.1 SAFETY CERTIFICATION The Blendtec Xpress blender (model ES3) is certified by ETL (Report No� 3018204-4, 3018204-2 & 3018204-3)� It also complies with UL 763, 3rd Ed, Nov 2000, and to CSA standard C22�2 No� 195-m 1987, Nov� 1990, R 2004�.
• 1.8 NEVER OPERATE IF THE UNIT APPEARS DAMAGED If the blender malfunctions call a Blendtec qualified service agent first� If it is dropped or damaged in any way, return the blender to a Blendtec qualified service agent immediately for examination, repair, electrical or mechanical adjustment, or possible replacement�. • 2.5 POWER SPECIFICATIONS The Xpress is certified for use on 220/240 volt circuits and is limited to 6�5 amps� It is required that this unit be installed with a 7�5 amp (or greater) circuit breaker or fuse�. Yakyuken Special 2 Psx on this page. • Figure 1 SIDE VIEW BLENDER BASE AND Jar ASSEMBLY Blade Power Switch Blender Base Power Cord Cover Figure 2 Front View BLENDER BASE Blender Drive Socket LCD Information Touch Pad Center. • Inspect all items to ensure no damage occurred in shipment� 5� If any damage has occurred contact a Blendtec qualified service agent immediately� 6� 3.2 RECORDING YOUR SERIAL NUMBER AND DATE OF SHIPMENT Record your blender base serial number and date of purchase in the space below� You will need these when contacting Blendtec for service�. • Check the blender jar for blockage� A reading of “NO TEMP� SENSOR” indicates the blender computer is not able to monitor motor temperature� Contact a Blendtec qualified service agent� BLADE STOPS: If the overload switch stops the blender, remove the blender jar and carefully check for blockage of the blade�. • Blender Base: Check to see if the excess noise is coming from the motor� Remove the jar from the blender base and press cycle number one� Listen to the motor sound without a jar attached� If it is excessively noisy, contact a Blendtec qualified service agent�. • SECTION 6 - WARRANTY AND SERVICE PROCEDURE 6.1 WARRANTY DESCRIPTION Blendtec warrants the Xpress Blender for 1 year, or 5,000 cycles which ever comes first� JAR: The jar and internal bearing assembly are warrantied against failure for one year from purchase date�.