Code: # Configuration for the usb_modeswitch package, a mode switching tool for # USB devices providing multiple states or modes # # This file is evaluated by the wrapper script 'usb_modeswitch_dispatcher' # in /usr/sbin # To enable an option, set it to '1', 'yes' or 'true' (case doesn't matter) # Everything else counts as 'disable' # Disable automatic mode switching globally (e.g. To access the original # install storage) DisableSwitching=0 # Enable logging (results in a extensive report file in /var/log, named # 'usb_modeswitch_' (and probably others) EnableLogging=0 # DAS edit 2011-07-20 # Cisco Valet Connector AM10 # # Contributor: ohmysql (quite the n00b so please help if you see errors) # No. 1 DefaultVendor= 0x1307 DefaultProduct= 0x0169 TargetVendor= 0x13b1 TargetProduct= 0x0031 #MessageEndpoint=0×01 MessageContent='3f'And here's what I get when I run. I know very little about usb_modeswitch, but I noticed your post went 15 hours without a peep, so maybe you'll accept a suggestion from an amateur. The error message is:However, 'message endpoint' is commented out in your.conf file oes the behavior improve if you remove the hash?Hello, Thanks for the reply. No, I've tried removing the hash and changing the value to a few things found on the internet - 01, 05 and it still says it can't find the endpoint.
Buy Cisco Valet AM10 300Mbps 802.11n Wireless LAN USB 2.0 Adapter w/Extension Cable: USB Network Adapters - Amazon.com FREE DELIVERY possible on. Buy Cisco Valet AM10 IEEE 802.11b/g/n USB 2. Tarif Douanier En Algerie Pdf. 0 Wireless Adapter 64/128-Bit WEP, WPA, WPA2 (Self-installs directly from USB) with fast shipping and top-rated customer service. Once you know, you Newegg!
Thanks for the suggestion - I've been googling trying to figure out where the end point of USB devices is listed. If only I had windows so I could plug this in and spy on how it works there. Maybe that would help. Code: sudo lsusb -vFeel free to redact the not-a-Cisco parts.Chili, you're a lot classier than I am. I've been cursing since I purchased this thing. More than anything, what you can do to help is just be someone to bounce ideas off.
I mean if you Google something and find different things than me, that's even better. Yeah, I've been trying to learn usb_modeswitch - I don't find it easy. To answer your question, I got those target numbers from here: Here are the AM10 parts of that code.
Note for some reason, there appears to be two devices? Code: lsusb Bus 001 Device 005: ID 1307:1169 Transcend Information, Inc. TS2GJF210 JetFlash 210 2GB Bus 001 Device 003: ID 1307:0169 Transcend Information, Inc. Ubuntu:~$ sudo lsusb -v Bus 001 Device 005: ID 1307:1169 Transcend Information, Inc. TS2GJF210 JetFlash 210 2GB Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x1307 Transcend Information, Inc. IdProduct 0x1169 TS2GJF210 JetFlash 210 2GB bcdDevice 1.00 iManufacturer 1 Cisco Systems, Inc. I think there are two devices; the flash drive part has the (Windows) software that drives the wireless device.